29mm slim body
Fits shallow ceiling voids, furniture recesses and joinery where a brick-style supply cannot go.
LED Power Supplies · CP Series
Designed for the evening, when lights run at ten percent
The CP Series is a 29mm slim constant voltage LED power supply that dims smoothly from full output down to about 1%, and accepts five kinds of dimmer on the same unit. 12V, 24V and 48V, from 60W to 200W.
- Height
- 29mm
- Output
- 12V · 24V · 48V
- Power
- 60W–200W
- Dimming
- 5 methods
01
Introduction
Most indirect lighting is seen dimmed. Specify for that moment.
A cove, a coffer or a shelf of linear light is usually commissioned at full brightness, in daylight, with the contractor on site. Then it lives most of its life at 10 to 30 percent: hotel corridors at night, a living room after dinner, a restaurant during service. That is where a cheap power supply gives itself away with a shimmer, a visible step, or a light that refuses to go low and then snaps off.
The CP Series is built for that end of the range. High-frequency PWM with soft start keeps output steady as it fades, and the LED can start from around 1 percent. And because the unit accepts Triac, 0-10V, 1-10V, 10V PWM and resistor control, it works with whatever dimmer the project finally lands on, in a body only 29mm high.
02
Control
Five dimming inputs on one supply
Choose the control that suits the room. The power supply stays the same.
- Triac (phase-cut)Standard wall dimmers, the usual choice for homes, hotel rooms and small retrofits.
- 0-10VBuilding management systems, KNX analogue outputs and commercial dimming panels.
- 1-10VCommercial dimming panels and controllers using the 1-10V signal.
- 10V PWMControllers and microcontroller outputs that send a PWM signal.
- ResistorA simple potentiometer knob, with no controller at all.
03
Models
Every model is 29mm high
Choose the voltage that matches your LED product, then the wattage with headroom above the connected load.
| Voltage | Power | Max current | L × W × H |
|---|---|---|---|
| 12V | 60W | 5.0 A | 145 × 48 × 29 mm |
| 12V | 100W | 8.3 A | 160 × 48 × 29 mm |
| 12V | 150W | 12.5 A | 180 × 64 × 29 mm |
| 12V | 200W | 16.7 A | 205 × 64 × 29 mm |
| 24V | 60W | 2.5 A | 145 × 48 × 29 mm |
| 24V | 100W | 4.2 A | 160 × 48 × 29 mm |
| 24V | 150W | 6.3 A | 180 × 64 × 29 mm |
| 24V | 200W | 8.3 A | 205 × 64 × 29 mm |
| 48V | 100W | 2.0 A | 160 × 49 × 29 mm |
| 48V | 150W | 3.0 A | 180 × 63 × 29 mm |
| 48V | 200W | 4.0 A | 205 × 63 × 29 mm |
04
Specifications
Technical data
| Driver type | Constant voltage |
|---|---|
| Output voltage | 12V, 24V or 48V DC |
| Output power | 60W, 100W, 150W, 200W (48V: 100W–200W) |
| Input | AC 100–240V, 50/60Hz |
| Dimming | Triac, 0-10V, 1-10V, 10V PWM, resistor |
| Dimming range | 0–100%, LED start from about 1% |
| Height | 29mm |
| Cooling | Free-air convection, fanless |
| Protection | Overload, over-temperature, short circuit, over-voltage, auto-recovery |
| Use | Indoor, Class I / II / III installations |
05
Features
What the CP Series brings to an installation
Five dimming methods
Triac, 0-10V, 1-10V, 10V PWM and resistor on one unit, so the dimmer can be decided late.
Smooth to about 1%
High-frequency PWM and soft start: no pop-on, no shimmer, no visible flicker at low levels.
Three output voltages
12V, 24V and 48V cover standard strip, long runs and 48V systems.
Fanless and silent
Free-air convection cooling with no moving parts, quiet in bedrooms and hotel rooms.
Auto-recovery protection
Overload, over-temperature, short circuit and over-voltage, with automatic restart once the fault clears.
Wide AC input
AC 100–240V, 50/60Hz for stable operation on varying site supplies.
Clear sizing
Four power ratings per voltage with published dimensions, so cavities can be detailed early.
Installation
Hidden, but never out of reach
A slim supply still needs service one day. Plan an access hatch or removable panel, leave air space around the body, keep it out of insulation, and route dim signal wires away from mains cabling.
06
Applications
Where a dimmable slim supply belongs
Aluminium profile runs
Dimmable power behind recessed and surface linear profiles.
Cove and coffer ceilings
Indirect light that fades evenly along the whole run.
Hotel rooms and corridors
Wall-dimmer control, quiet and concealed.
Retail shelving
Scene dimming from a 0-10V panel.
Offices
Indirect light set to suit daylight and screen work.
Luxury residences
A simple wall dimmer for strip lighting in living and bedrooms.
Restaurants and bars
Low, steady light through the evening service.
Wardrobes and cabinetry
Slim enough for furniture voids and plinths.
Neon flex installations
Dimmable constant voltage for 12V and 24V neon flex.
07
FAQ
Installation and specification questions
Triac (phase-cut) wall dimmers, 0-10V, 1-10V, 10V PWM and resistor (potentiometer) control are all supported on the same unit. Pick the control that suits your wall dimmer, BMS or controller.
Dimming runs from 0 to 100 percent, and the LED can start from about 1 percent. High-frequency PWM with soft start keeps the light steady at low levels, with no visible flicker.
Multiply the strip's watts per metre by the total length, then choose a supply comfortably above that load rather than at its limit. A margin of around 20% keeps the unit cooler in an enclosed cavity and extends its life.
Always match the voltage of your LED product. For new designs, 24V suits most strip runs; 12V suits short runs up to about 5 metres per feed; 48V suits very long runs or 48V-rated strip.
Every model is 29mm high. Length and width depend on wattage, from 145 × 48mm at 60W to 205 × 64mm at 200W, so check the footprint of your chosen model against the space.
No heatsink or fan is needed; it cools by free-air convection. Leave some air space around the body and do not cover it with insulation.
The supply protects itself against overload, over-temperature, short circuit and over-voltage, and restarts automatically once the fault is removed. There is no fuse to replace.
It is designed for indoor use in Class I, II and III installations. Mount it in a dry, accessible location, away from moisture and splash zones.
Need help sizing a dimmable supply?
Send your strip type, run lengths and control method, and we will recommend the voltage and wattage.
